Auralex SheetBlok Sound Isolation Barrier is a dense, limp-mass vinyl material that is about 6dB more effective than solid lead at stopping the transmission of sound. It acts as a thin, dense sound barrier layer in walls, ceilings or floors and is most effective when used as one component of a multi-layered soundproofing construction scheme.
SheetBlok helps in decoupling (i.e., floating) floors and walls and, while it's not normally considered a finish product per se, it is paintable with latex paint. SheetBlok can also be used to wrap HVAC ducting, as a vent noise blocker, as a pipe noise insulator or under carpet/carpet pad. It can also be doubled up, increasing its effectiveness from STC 27 to about STC 35. Auralex SheetBlok holds up under harsh environments and cuts easily with a utility knife or scissors.
- Vinyl material, 6dB more effective than solid lead
- Thin, dense sound barrier
- Use in walls, ceilings or floors
- Most effective when combined with other soundproofing constuction
- Helps in decoupling floors and walls
- Can be used with HVAC ducts, as a vent noise blocker, pipe noise insulator or under carpet
- Holds up under harsh environments
- Passes test MVSS-302* for flammability
- STC: 27
- Mounts directly to sheetrock & subflooring
- Available in 4’ x 10’ and 4’ x 30’ rolls
- Is resistant to oil, grease and most solvents
WHAT'S IN THE BOX?
- 1 Roll - Auralex SheetBlok Sound Isolation Barrier (choose length)
- Treatment Type: Construction/Insulation
- Dimensions: 4'W x 10'L (40 sq. ft) Roll or 4'W x 30'L (120 sq. ft) Roll
- Roll Weight: 4’x10′ Roll = 45 lbs – 4’x30′ Roll = 128 lbs
- Thickness: 1/8"
- STC: 27
- Color: Black (smooth on one side, pebble grain finish on the other side)
- Weight: 1# - 1.1# per square foot
- Service Temperature: -40° to 180° F
- Tensile Strength: 400 psi Tear Strength: 70#/inch
- Flammability: Self-Extinguishing, Rated UL94 S.E. "0"; Passes test MVSS-302
- Manufacturer Part No.:
- 4' x 10' Roll: J10SHBL
- 4' x 30' Roll: J30SHBL
Installation Tips:The best method for installing Auralex SheetBlok in a wall, ceiling or floor construction is sandwiched between other layers. Why?
- Sandwiching provides a resilient layer between two solid layers. In addition to offering more mass, this will decouple layers. Technically, this is known as an "impedance mismatch." Sound energy is more impeded by the sandwiching effect than by other installations.
- Sandwiching is usually easier. Gluing to the first layer of drywall is usually all that is necessary. The final layer of drywall can be glued and screwed right on top of the SheetBlok.
- The final layer of drywall is more aesthetically pleasing than if the room were finished with SheetBlok. SheetBlok is black, which is not "pretty." Using it as a finish layer also means additional mechanical fastening is necessary - button-cap nails or trim strips.
- Attached directly to the studs. Other layers would go over the SheetBlok. Disadvantages: Since there is no solid sub-layer, sealing the seams is difficult. Also, the decoupling achieved when used as the "meat" in the "sandwich" is not available in this installation.
- Cut into strips and used only on the studs. While this certainly reduces cost, a main disadvantage is not using the SheetBlok as a barrier.
- Cut into strips and placed as a double layer between the sill plate and the subfloor. This helps decouple walls from the floor.
- Cut into strips and placed between the top plate and the ceiling joists. This helps decouple the walls from the ceilings.
- As a layer on the insides of loudspeaker cabinets. This is very popular in home theater setups where special loudspeaker cabinets have been built around a large screen or TV.
- Cut into 2'x4's or 2'x2's and laid on the back of ceiling tiles. While not a "fix" for sound transmission through acoustical tile ceilings, this does add a lot of mass to the ceiling and should nominally improve ceiling performance. This is sometimes the only alternative short of replacing the entire ceiling. (Note: An acoustic ceiling professional should help you recalculate the number of grid hangers you need.)